Ev> Blog> Magnetic Flap Level Gauge Components Damage and Troubleshooting

Magnetic Flap Level Gauge Components Damage and Troubleshooting

November 19, 2021

Magnetic flap level gauge components damage failure and treatment:

Magnetic flap level gauge in the practical application of often failure, of these failures, some caused by a single component failure, some caused by simultaneous failure of multiple components. Magnetic flap level gauge common fault and its causes are as follows:

A: The display panel is abnormal

The reasons for this failure are usually the following:

1, the gap between the flap and the guideway design unreasonable or too small, resulting in friction is too large, the flip does not flip;

2, the distance between the display panel and the buoy is too large, the magnetic drive force of the buoy is insufficient, which causes the flip not to flip;

3, the magnet in the flip is too small or the magnetic force disappears, resulting in flip does not flip or flip abnormalities;

4, water or dust and other impurities infiltrated the display panel, resulting in flip flip difficult;

5, the ambient temperature is too low, causing the media to freeze, the float can not move, flip the liquid level can not be displayed properly.

Second: the local show normal, remote display is not normal

In general, there are several common reasons for this failure:

1, domestic reed pipe glass fragile, reed pipe short circuit or open, will lead to abnormal remote transmission;

2, resistance Weld;

3, the reed switch metal contact gap is very small, when the medium temperature is too high, the sheet metal when heated expansion, prone to closed state;

4, the pressure exceeds the rating, resulting in switch damage.

Three: remote and magnetic flap are not moving

This failure phenomenon is usually caused by abnormal floats, the following two kinds of performance:

Phenomenon one: the float is stuck, resulting in the display panel instructions are not correct.

Failure Analysis: Floating magnetic flap level gauge stuck, usually for the following reasons:

1, when the float used for a period of time, the float may be stuck due to the presence of impurities, can not rise or fall;

2, buoy installation angle is less than 87 degrees, leading to tilt, affect the float up and down movement;

3, the float due to its own magnetic adsorption of iron or other dirt caused by stuck;

4, the ambient temperature is too low, causing the media to freeze, the float can not move.

Phenomenon two: Float damage, resulting in the display panel instructions are not correct.

Failure Analysis: Floating magnetic level gauge floater damage, usually for the following reasons:

1, the float due to the strength of the design is wrong, resulting in pressure to the inside of the depression, deflated;

2, no welding penetration or welding at the weld, resulting in pressure when the weld cracks, floats into the water;

3, the float due to the use of a long time or long-term high temperature use, demagnetization, resulting in unusable;

4, the float in the magnet loose, resulting in the float can not work.

【Print】 【Close】
Contal ABD

Yazar:

Mr. Huang Yiyu

E-posta:

sales@xigeled.cn

Phone/WhatsApp:

+8613751262319

Popüler Ürünler
Blog Haberleri
Ayrıca sevebilirsiniz
İlgili Kategoriler

Bu tedarikçi için e-posta

Konu:
E-posta:
İleti:

Mesajınız MSS

Contal ABD

Yazar:

Mr. Huang Yiyu

E-posta:

sales@xigeled.cn

Phone/WhatsApp:

+8613751262319

Popüler Ürünler
Blog Haberleri
Dongguan XINYUDA Technology Co., Ltd. Dongguan Xinyuda Technology Co., Ltd., 1990'larda LED Ar -Ge ve Yatırım'a odaklanarak Hong Kong Konlida International Group Co., Ltd. tarafından Hong Kong'da kurulmuştur. On yıldan fazla...

Bültenimize abone olun

  • Mobile-Phone
    +8613751262319
  • Adres
    Room 202, Building 4, No. 3, East Siheng Road, Lianhu, Tangxia Town, Dongguan, Guangdong China
We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Gönder