Ev> Blog> LED light-emitting diode welding technical requirements

LED light-emitting diode welding technical requirements

January 29, 2022

White light (blue light, green light and white light) LED diodes should strictly observe the following requirements during soldering:

1. Workers must wear anti-static gloves, anti-static wrists, and electric soldering irons must be grounded. It is strictly forbidden to touch the two lead pins of white LEDs with bare hands. Because the anti-static of white LED is 100V, and the human body working humidity on the workbench is 60%-90%, the static electricity of the human body will damage the crystal layer of the LED. After working for a period of time (such as 10 hours), the diode will be invalid (not bright). In case of seriousness, it will immediately expire.

2. The soldering temperature is 260 ° C, 3 seconds. If the temperature is too high, it will burn out the chip if it takes too long. In order to better protect the LED, the LED colloid and the PC board should be kept at a distance of 2mm or more, so that the solder heat is dissipated in the pin.

3. The normal operating current of the LED is 20mA, and small fluctuations in voltage (such as 0.1V) will cause large fluctuations in current (10%-15%). Therefore, in the circuit design, different current limiting resistors should be paired according to the voltage drop of the LED to ensure that the LED is in the best working condition. If the current is too large, the LED will shorten the life and the current will be too small to reach the required light intensity. Our company will split the LEDs when they are delivered in batches, that is, the LED light intensity, voltage and light color in the same package are consistent, and are indicated on the spectrometer.

(1) Soldering iron soldering: soldering iron (up to 30W) tip temperature does not exceed 300 ° C; welding time does not exceed 3 seconds; welding position is at least 2 mm from the colloid.

(2) Wave soldering: The maximum temperature of the dip soldering is 260 ° C; the dip soldering time is not more than 5 seconds; the dip soldering position is at least 2 mm from the colloid.

LED welding curve pin forming method:

(1) It is necessary to bend the bracket 2 mm away from the gel.

(2) Bracket forming must be done with a clamp or by a professional.

(3) Bracket forming must be completed before welding.

(4) Bracket forming must ensure that the pins and spacing are consistent with the board.

Cleaning

Special care must be taken when cleaning the gel with chemicals, as some chemicals damage the surface of the gel and cause fading such as trichloroethylene, acetone, and the like. It can be wiped and immersed in ethanol for less than 3 minutes at room temperature.

Electrostatic protection Electrostatic and current surges will cause damage to LEDs. Use Instatic products such as protective tapes and gloves when using InGaN series products.

Bizimle iletişime geçin

Author:

Mr. Huang Yiyu

E-posta:

sales@xigeled.cn

Phone/WhatsApp:

+8613751262319

Popüler Ürünler
You may also like
Related Categories

Bu tedarikçi için e-posta

Konu:
E-posta:
İleti:

Your message must be betwwen 20-8000 characters

Bizimle iletişime geçin

Author:

Mr. Huang Yiyu

E-posta:

sales@xigeled.cn

Phone/WhatsApp:

+8613751262319

Popüler Ürünler
Dongguan XINYUDA Technology Co., Ltd. Dongguan Xinyuda Technology Co., Ltd., 1990'larda LED Ar -Ge ve Yatırım'a odaklanarak Hong Kong Konlida International Group Co., Ltd. tarafından Hong Kong'da kurulmuştur. On yıldan fazla...

NewsLetter

  • Mobile-Phone
    +8613751262319
  • Adres
    Room 202, Building 4, No. 3, East Siheng Road, Lianhu, Tangxia Town, Dongguan, Guangdong China
We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Gönder